Posts

All the articles I've posted.

• Frigidaire Washer Won't Agitate - Causes & Fix

  8 Jun, 2026

  Worn agitator dogs or a failed drive coupler usually stop agitation. Replace the agitator repair kit or coupler to restore wash action.

• GE Washer Overflowing - Causes & Fix

  8 Jun, 2026

  A GE washer overflowing usually means a failed water inlet valve that won't close or a clogged pressure hose preventing level detection.

• GE Washer Won't Agitate - Causes & Fix

  8 Jun, 2026

  A worn or slipping drive belt is the most common cause. Enter diagnostic mode to retrieve fault codes, then inspect the belt and pulleys for wear or blockage.

• Maytag Washer Smells Like Mildew - Causes & Fix

  8 Jun, 2026

  Wet laundry left inside and a closed door prevent drying, leading to mildew buildup. Remove loads promptly, leave the door open, and run a Clean Washer cycle with hot water.

• Whirlpool Washer Won't Agitate - Causes & Fix

  8 Jun, 2026

  Most often caused by a worn cam/splutch or shift actuator that no longer engages agitate mode. Check drive parts in service mode.

• LG Washer Won't Agitate - Causes & Fix

  8 Jun, 2026

  A stripped wash plate hub or failed hall sensor on direct-drive models is usually the culprit. Check for free-spinning plates and test motor sensors.

• Yaskawa GA800 A.116 Fault - Causes & Fix

  8 Jun, 2026

  A.116 means multi-function input open alarm on GA800 VFDs. Most often an open interlock, E-stop, or loose wiring. Check control circuit.

• Yaskawa GA800 A.112 Alarm - Causes & Fix

  8 Jun, 2026

  A.112 on a Yaskawa GA800 is an alarm for missing or invalid run/reference input. Most often the command source is set wrong on the keypad.

• Maytag Dryer F6E2 Error Code - Causes & Fix

  8 Jun, 2026

  F6E2 on a Maytag dryer means a communication fault between the main control and user interface. Power-cycle for 5 minutes first.

• Maytag Dryer F3E2 Error Code - Causes & Fix

  8 Jun, 2026

  F3E2 means the moisture sensor has not registered data for five consecutive loads. Most often the dryer is not level or loads are too small.

• Maytag Dishwasher F8E4 Error Code - Causes & Fix

  8 Jun, 2026

  F8E4 means water in the drip tray has triggered the leak float switch. Most often a loose fill valve connection or supply line leak.

• Maytag Range F7 Error Code - Causes & Fix

  8 Jun, 2026

  F7 on a Maytag range means a stuck or shorted key on the touchpad, or a keypad/control-board fault. Replace the keypad assembly first.

• Maytag 5A6 Error Code - Causes & Fix

  8 Jun, 2026

  5A6 means Sabbath mode is active on your Maytag range. Exit it using the Temp/Time button sequence or power-cycle at the breaker.

• GE Dishwasher F56 Error Code - Causes & Fix

  8 Jun, 2026

  F56 means the dishwasher did not drain. Check the drain hose for kinks, the air gap for clogs, and the disposer knockout plug first.

• Frigidaire SB Error Code - Causes & Fix

  8 Jun, 2026

  SB means Sabbath Mode is active, not a failure. Lights and dispenser won't work, but cooling continues. Fix: hold the model-specific buttons for 5 seconds to exit.

• Frigidaire E15 Error Code - Causes & Fix

  8 Jun, 2026

  E15 means a communication fault between the user interface and main control board. Most often caused by a loose wiring harness.

• Frigidaire Refrigerator dF Error Code - Causes & Fix

  8 Jun, 2026

  dF means a defrost-circuit fault. The most common fix is replacing the defrost control board or checking the wiring harness and connectors.

• Bosch E02 Error Code - Causes & Fix

  8 Jun, 2026

  E02 on Bosch dishwashers means a main control board relay fault in the heating circuit. Most often the control board itself has failed.

• Whirlpool F1E1 Error Code - Causes & Fix

  8 Jun, 2026

  F1E1 on Whirlpool means a control fault. Power-reset first: unplug or flip the breaker for 5 minutes then test again.

• Whirlpool Range PF Error Code - Causes & Fix

  8 Jun, 2026

  PF means power failure detected by the control. Press Cancel to clear it. If it returns, check your breaker and terminal-block wiring.

• Whirlpool F3 Error Code - Causes & Fix

  8 Jun, 2026

  F3 means an oven temperature sensor circuit fault. Most often the sensor probe has failed and needs replacement.

• Whirlpool Oven LOC Error Code - Causes & Fix

  8 Jun, 2026

  LOC means the control lock (child lock) is enabled on your Whirlpool oven. Press and hold START/ENTER for 5 seconds to unlock the keypad.

• Whirlpool Oven F9 Error Code - Causes & Fix

  8 Jun, 2026

  F9 or F9 E0 means miswired outlet or incorrect voltage detected at startup. Reset power at the breaker for 1 minute first.

• Whirlpool Dryer F4E4 Error Code - Causes & Fix

  8 Jun, 2026

  F4E4 on a Whirlpool electric dryer means a power-supply voltage fault. Most often one breaker pole has tripped or voltage is low.