Posts

All the articles I've posted.

• Whirlpool F7E1 Error Code - Causes & Fix

  8 Jun, 2026

  F7E1 means motor speed sensing fault. Most often shipping bolts still installed or shift actuator failed. Reset and check load first.

• Whirlpool F5E1 Error Code - Causes & Fix

  8 Jun, 2026

  F5E1 means the door switch or lid lock is not detected as closed. Most often the door is obstructed or the lock assembly has failed.

• Whirlpool F3E1 Error Code - Causes & Fix

  8 Jun, 2026

  F3E1 means the washer cannot detect water level. The most common fix is clearing a clogged or kinked pressure hose or air dome.

• Whirlpool Washer F3E2 Error Code - Causes & Fix

  8 Jun, 2026

  F3E2 means a water-temperature sensor fault. Most often a broken sensor wire or failed thermistor. Check wiring first, then swap sensor.

• Whirlpool Washer F21 Error Code - Causes & Fix

  8 Jun, 2026

  F21 means drain problem or drain time too long. Most often caused by a kinked drain hose or clogged pump filter. Check hose first.

• Whirlpool Washer F2E1 Error - Causes & Fix

  8 Jun, 2026

  F2E1 means a stuck key or user interface fault. Most often a stuck button or failed keypad. Unplug 5 minutes to reset first.

• Whirlpool F1E2 Error Code - Causes & Fix

  8 Jun, 2026

  F1E2 on Whirlpool means different things by product: control-panel fault (washers) or UL A/D error (ovens). Often fixed by a 5-minute reset.

• Whirlpool F1E1 Error Code - Causes & Fix

  8 Jun, 2026

  F1E1 on Whirlpool means a control fault. Power-reset first: unplug or flip the breaker for 5 minutes then test again.

• Whirlpool F0E1 Error Code - Causes & Fix

  8 Jun, 2026

  F0E1 on Whirlpool washers means the Clean Washer cycle started with items still inside. Remove all contents and restart the cycle empty.

• Whirlpool Refrigerator PO Error Code - Causes & Fix

  8 Jun, 2026

  PO means Power Outage: the freezer warmed to 18°F or higher. Press MEASURED FILL to clear the alert, then check your breaker and outlet.

• Whirlpool Refrigerator E9 Error Code - Causes & Fix

  8 Jun, 2026

  E9 means the freezer temperature is too high. Most often caused by a door left ajar or warm food loaded in. Reset power for 1 minute first.

• Whirlpool Refrigerator E5 Error - Causes & Fix

  8 Jun, 2026

  E5 on Whirlpool refrigerators signals an ice-maker temperature sensor mismatch. Most often the ice-room thermistor has failed.

• Whirlpool Refrigerator E4 Error Code - Causes & Fix

  8 Jun, 2026

  E4 signals a defrost sensor fault in the fresh-food compartment. Most often a failed sensor or wiring; reset power first.

• Whirlpool Refrigerator dF Error Code - Causes & Fix

  8 Jun, 2026

  dF means defrost failure on Whirlpool refrigerators. The most common fix is replacing the defrost heater or defrost thermostat.

• Whirlpool Range PF Error Code - Causes & Fix

  8 Jun, 2026

  PF means power failure detected by the control. Press Cancel to clear it. If it returns, check your breaker and terminal-block wiring.

• Whirlpool Range SAB Error Code - Causes & Fix

  8 Jun, 2026

  SAB means Sabbath Mode is on, not a fault. Turn off Sabbath Mode using your model's key sequence (check the owner's manual).

• Whirlpool Range LOC Error Code - Causes & Fix

  8 Jun, 2026

  LOC means the control lock feature is enabled, not a fault. Press and hold START/ENTER for 5 seconds to unlock the keypad and restore use.

• Whirlpool Range LOC Error Code - Causes & Fix

  8 Jun, 2026

  LOC means Control Lock is enabled, not a failure. Press and hold START/ENTER for 5 seconds to unlock. If it persists, reset the breaker.

• Whirlpool Range FC E5 Error - Causes & Fix

  8 Jun, 2026

  FC E5 on a Whirlpool range signals a Wi-Fi antenna or wiring fault. Most often a loose connector or failed antenna module.

• Whirlpool FC E4 Error Code - Causes & Fix

  8 Jun, 2026

  FC E4 on a Whirlpool wall oven signals a Wi-Fi antenna or wiring fault. Most likely fix: power-cycle the oven at the breaker.

• Whirlpool FC E3 Error - Causes & Fix

  8 Jun, 2026

  FC E3 means the range lost its Wi-Fi connection to your router. Most often fixed by power-cycling the range and resetting the router.

• Whirlpool Range FC E2 Error - Causes & Fix

  8 Jun, 2026

  FC E2 is not a verified Whirlpool range code. You likely saw F3 E2 (oven sensor fault) or F2 E2 (keypad connection fault).

• Whirlpool Range F9 Error Code - Causes & Fix

  8 Jun, 2026

  F9 / F9 E0 means the range detected a power-supply or wiring problem. Most often fixed by checking the outlet and terminal connections.

• Whirlpool Range F8 Error Code - Causes & Fix

  8 Jun, 2026

  F8 on a Whirlpool range means meat probe or cooling fan fault. Most often the meat probe is not fully seated in the jack.