Posts
All the articles I've posted.
-
Yaskawa A1000 oS Fault Code - Causes & Fix
oS signals an internal self-diagnostic or control-circuit fault. Cycle power first. If it returns, replace the control board or drive.
-
Yaskawa A1000 oPr Fault Code - Causes & Fix
oPr means the external operator/keypad is disconnected or the control cable has failed. Reseat the keypad connector at the drive.
-
Yaskawa A1000 CPF03 - Causes & Fix
CPF03 on a Yaskawa A1000 means a control board connection error. The most common fix is reseating the control board connector.
-
ABB ACS880 Fault Codes - Causes & Fix
ABB ACS880 fault codes indicate drive problems like overcurrent, overvoltage, or overtemp. Most common: check motor cables and cooling.
-
Amana Washer Lid Error Code - Causes & Fix
LdL means lid won't lock; LdU means lid won't unlock. Most common fix: remove obstructions from lid area and power-cycle washer.
-
Amana Dryer F3 E2 Error Code - Causes & Fix
F3 E2 does not exist for Amana dryers. This code applies to Amana washers and indicates a water temperature sensor circuit fault.
-
Samsung Microwave Door Won't Open - Causes & Fix
Usually caused by a broken door hook, latch spring, or release lever. Unplug, inspect the latch mechanism, and replace broken parts.
-
Samsung Microwave Making Loud Noise - Causes & Fix
Usually normal magnetron hum or vent fan. Check turntable parts, clean cavity, and test with water bowl to rule out food noise.
-
Samsung Microwave Won't Turn Off - Causes & Fix
Most often a shorted touchpad or dirty ribbon cable between the keypad and control board. Disconnect the ribbon to isolate the fault.
-
Kenmore Oven Display Not Working - Causes & Fix
A dead display usually means the main control board isn't sending power to the display board. Check incoming power first, then replace the main control board if needed.
-
Kenmore Oven Clicking but Won't Light - Causes & Fix
A weak or failed oven igniter is the most common cause. The igniter glows but doesn't draw enough current to open the gas valve.
-
Kenmore Oven Heats Too Hot - Causes & Fix
Most often a failed oven temperature sensor sending incorrect readings to the control board. Test sensor resistance at room temp.
-
Kenmore Oven Won't Stop Beeping - Causes & Fix
Usually a failed temperature sensor triggering a false overheat alarm (F10). Power-cycle the oven, then test or replace the sensor.
-
Kenmore Oven Self-Clean Not Working - Causes & Fix
Usually a failed door lock assembly that won't latch or report locked status. Check that the door closes fully, then test the lock motor and switch.
-
Kenmore Oven Door Won't Lock - Causes & Fix
A failed door lock motor or control board is usually why a Kenmore oven door won't lock. Replace the lock assembly or main control.
-
Kenmore Oven Burner Won't Light - Causes & Fix
Weak or failed oven igniter is the most common cause. Test it for glow and amperage draw, then replace if it pulls below 3.0 amps.
-
Kenmore Oven Igniter Not Working - Causes & Fix
A weak hot-surface igniter that glows but doesn't draw enough current to open the gas valve is the most common cause. Replace the igniter.
-
Kenmore Oven Broiler Not Working - Causes & Fix
Most often a burned-out broil element. Check the element for visible breaks or blistering, then test for continuity and replace if open.
-
Kenmore Oven Temperature Not Accurate - Causes & Fix
A Kenmore oven running too hot or cold is usually caused by a miscalibrated control or a failed temperature sensor. Test with an oven thermometer and recalibrate through the control panel, or replace the sensor if it reads far from 1,080 ohms at room temperature.
-
Kenmore Oven Won't Turn On - Causes & Fix
Most often caused by a tripped breaker cutting power to the oven. Reset the breaker and verify 240V at the outlet with a multimeter.
-
Kenmore Oven Not Heating - Causes & Fix
A burnt-out bake element (electric) or weak igniter (gas) is the most common cause. Test for continuity or observe glow, then replace.
-
Maytag Oven Clicking but Won't Light - Causes & Fix
Usually a gas supply shutoff, clogged burner ports, or moisture in the igniter area. Check gas supply, clean ports, and dry wet areas first.
-
Maytag Oven Display Not Working - Causes & Fix
Most often Control Lock is enabled or a power interruption put the control into a fault state. Reset the breaker for 1 minute.
-
Maytag Oven Heats Too Hot - Causes & Fix
A faulty temperature sensor is the most common cause. Compare actual oven temp with a manual thermometer and replace the sensor if needed.