Tag: microwave

All the articles with the tag "microwave".

• Whirlpool WMC30516HZ Microwave Problems & Error Codes

  1 Jun, 2026

  Door-error messages are most common, usually from a failing latch or misalignment. Reset power first, then inspect the door system.

• Panasonic NN-SN67KS Microwave Problems & Error Codes

  1 Jun, 2026

  H97/H98/H99 inverter codes are the most common faults on the NN-SN67KS, usually fixed by replacing the inverter board or magnetron.

• LG MVEL2033F Microwave Problems & Error Codes

  1 Jun, 2026

  Door latch and interlock switch failures cause most DOOR errors. Clean latch area, check alignment, and replace the switch assembly if needed.

• GE JVM6175SKSS Microwave Problems & Error Codes

  1 Jun, 2026

  F1 open thermal sensor error is most common, usually from a failed cavity sensor or loose wiring. Replace the sensor or repair the harness.

• Panasonic NN-SN686S Microwave Problems & Error Codes

  1 Jun, 2026

  H98 and H97 error codes are the most common faults, usually caused by a failed inverter board or magnetron in the microwave power system.

• LG LMV2031ST Microwave Problems & Error Codes

  1 Jun, 2026

  F2 temperature errors from failed thermistor circuits are the most common fault on the LMV2031ST. Power reset, then replace the thermistor.

• Samsung ME21M706BAS Microwave Problems & Error Codes

  1 Jun, 2026

  SE error (key short) is most common on ME21M706BAS, usually caused by moisture or a faulty membrane keypad after steam or spills.

• GE JVM3160RFSS Microwave Problems & Error Codes

  1 Jun, 2026

  Most JVM3160RFSS units throw F-codes from failed sensors or touch panel shorts. Reset the control first, then replace the bad part.

• Kenmore Microwave E1 Error Code - Causes & Fix

  31 May, 2026

  E1 means a thermistor sensing fault. The control board isn't receiving proper temperature feedback. Replace the thermistor or fix wiring.

• Whirlpool Microwave F05 Error Code - Causes & Fix

  31 May, 2026

  F05 signals a door latch system fault. Usually a stuck latch, bad switch, or loose wire. Reset power first, then inspect the latch.

• LG Microwave F13 Error Code - Causes & Fix

  31 May, 2026

  F13 means a voltage error in your LG microwave. LG requires service for this fault. Unplug for one minute, then call a tech if it returns.

• LG Microwave F1 Error Code - Causes & Fix

  31 May, 2026

  F1 on an LG microwave means a mainboard fault. Most likely fix: replace the main control board after checking power and connections.

• Samsung Microwave E-82 Error - Causes & Fix

  31 May, 2026

  E-82 means a communication short error between control circuits. Power-cycle for 60 seconds. If it returns, call service.

• Kenmore Microwave PF Error Code - Causes & Fix

  31 May, 2026

  PF means power failure detected. The microwave lost incoming power briefly. Clear the code by pressing Cancel or unplug for 60 seconds.

• Kenmore Microwave SE Error Code - Causes & Fix

  31 May, 2026

  SE means a shorted or stuck keypad. Most often fixed by cleaning the touchpad or replacing the membrane keypad assembly.

• Kenmore Microwave F9 Error Code - Causes & Fix

  31 May, 2026

  F9 on a Kenmore microwave signals inverter failure or a door-switch fault. Most often: a bad inverter board or misaligned door latch.

• Kenmore Microwave F5 Error Code - Causes & Fix

  31 May, 2026

  F5 on Kenmore microwaves means humidity sensor or damper switch failure. The fix is replacing the failed sensor or switch after testing.

• Kenmore Microwave F4 Error Code - Causes & Fix

  31 May, 2026

  F4 means humidity sensor open or sensing error. Most often fixed by reconnecting the sensor wire or replacing the humidity sensor.

• Kenmore Microwave F3 Error Code - Causes & Fix

  31 May, 2026

  F3 on Kenmore microwaves typically means a thermistor/temperature sensor fault. Most often the thermal probe has failed or its wiring is loose.

• Kenmore Microwave E11 Error - Causes & Fix

  31 May, 2026

  E11 on a Kenmore microwave means a humidity sensor fault. The most common fix is replacing the failed humidity sensor.

• Kenmore Microwave E2 Error Code - Causes & Fix

  31 May, 2026

  E2 means thermistor error on Kenmore microwaves. The control board isn't reading valid temperature from the sensor. Replace the thermistor.

• Panasonic H99 Error Code - Causes & Fix

  31 May, 2026

  H99 indicates a magnetron or inverter circuit fault. Most common fix: replace the inverter board or magnetron after testing.

• Panasonic H98 Error Code - Causes & Fix

  31 May, 2026

  H98 means a high-voltage or heating-system fault in your Panasonic inverter microwave. Usually requires Power PCB or magnetron replacement.

• Panasonic Microwave U50 Error Code - Causes & Fix

  31 May, 2026

  U50 means your Panasonic microwave is overheated. Let it cool completely, clear blocked vents, and retry before calling service.