Tag: dishwasher

All the articles with the tag "dishwasher".

• KitchenAid F8E2 Error Code - Causes & Fix

  30 May, 2026

  F8E2 means a drain pump electrical fault. Most likely fix: replace the drain pump or repair its wiring harness and connectors.

• KitchenAid Dishwasher F6E3 Error Code - Causes & Fix

  30 May, 2026

  F6E3 means excessive suds detected in the tub. Usually caused by wrong detergent or too much detergent. Clear foam and run empty cycles.

• KitchenAid F3E2 Error Code - Causes & Fix

  30 May, 2026

  F3E2 on KitchenAid ovens/ranges signals a faulty oven or warming-drawer temperature sensor. Power-cycle first, then check the sensor.

• KitchenAid F1E2 Dishwasher Error - Causes & Fix

  30 May, 2026

  F1E2 means a failed or incompatible electronic control board. Most often you'll replace the main control to clear the fault.

• LG Dishwasher CR Error Code - Causes & Fix

  30 May, 2026

  CR means your LG dishwasher is stuck in test mode (Continuous Run). Press POWER to turn it off, then power-cycle the unit to exit.

• KitchenAid Dishwasher F1E1 Error - Causes & Fix

  30 May, 2026

  F1E1 means a stuck relay on the control board. The dishwasher drains then stops. Fix: power reset first, then replace the board.

• LG Dishwasher bE Error Code - Causes & Fix

  30 May, 2026

  bE means bubble error: excessive suds detected. Usually caused by wrong detergent or too much detergent. Run empty cycle, switch to powder.

• LG Dishwasher PE Error Code - Causes & Fix

  30 May, 2026

  PE means a water level sensor problem. Most often fixed by clearing the pressure hose or replacing the sensor itself.

• Samsung Dishwasher oE Error Code - Causes & Fix

  30 May, 2026

  oE means over-level water detected. Usually caused by a blocked filter or drain hose stopping water from draining out properly.

• Samsung Dishwasher LE Error Code - Causes & Fix

  30 May, 2026

  LE (or LC) means your Samsung dishwasher detected water in the base pan or leak sensor zone. Most often fixed by finding and repairing the leak, then drying the pan and resetting.

• Samsung Dishwasher CE Error Code - Causes & Fix

  30 May, 2026

  CE means a communication error between the control panel and main board. Most often fixed by a power reset or replacing a failed board.

• Samsung SE Error Code - Causes & Fix

  30 May, 2026

  Samsung SE code means the dishwasher can't drain water in time. Most often caused by a kinked drain hose or clogged filter.

• Samsung SC Error Code - Causes & Fix

  30 May, 2026

  SC means drain error. Clean the filter and sump, check for kinked drain hose, and verify the disposal knockout plug was removed.

• Whirlpool F10E5 Error Code - Causes & Fix

  30 May, 2026

  F10E5 means the cycle ended and drained, then displayed the fault. Most often it's a diverter issue or water leak in the base pan.

• Whirlpool Dishwasher FAE5 Error Code - Causes & Fix

  30 May, 2026

  FAE5 means the cycle ended and drained with a fault. Press Cancel twice and start a new cycle. If it returns, check for leaks in the base pan.

• Whirlpool F8E5 Dishwasher Error - Overfill & Fix

  30 May, 2026

  F8E5 means your Whirlpool dishwasher detected a flood and started draining. Most often water leaked into the base and tripped the float.

• Whirlpool Dishwasher F7E2 Error - Causes & Fix

  30 May, 2026

  F7E2 means high water temperature fault. Usually caused by a failed thermistor or loose sensor connection. Power cycle first.

• Whirlpool F6E3 Dishwasher Error - Causes & Fix

  30 May, 2026

  F6E3 means excessive suds detected. Most often caused by wrong detergent or too much detergent. Remove foam and run empty cycles to clear.

• Whirlpool F4E3 Error Code - Causes & Fix

  30 May, 2026

  F4E3 means the control lost communication with the circulation pump motor. Most often a failed pump motor, loose wiring, or blockage.

• Whirlpool F1E1 Dishwasher Error - Causes & Fix

  30 May, 2026

  F1E1 means your Whirlpool dishwasher starts draining, then stops. Most often a blocked drain hose, bad pump, or control issue.

• Whirlpool Dishwasher E6 Error Code - Causes & Fix

  30 May, 2026

  E6 / F6E6 signals a water supply or filling fault. Check that the shutoff valve is fully open, then reset power for one minute.

• Whirlpool Dishwasher E4 Error Code - Causes & Fix

  30 May, 2026

  E4 means water in the base pan. Most often a loose inlet hose connection. Press Cancel twice, dry the pan, check all fittings.

• Whirlpool Dishwasher E1 Error Code - Causes & Fix

  30 May, 2026

  E1 means a water-fill problem from siphoning. Check the drain hose is looped at least 20 in. above the floor and above the trap.

• Whirlpool E15 Error Code - Causes & Fix

  30 May, 2026

  E15 means water detected in the base leak tray. Most often caused by a worn door seal or loose hose. Dry the base and fix the leak.