How do I fix Frigidaire Oven Spark Module Replacement - Signs & How-To?

Follow the step-by-step diagnosis below. The most likely fix is identified by checking power, sensor resistance, and control-board signals in order — using a multimeter and the part numbers documented in the parts reference table.

Can I keep running the equipment with this fault active?

Generally no. Faults on Appliance units are emitted when a sensor, safety, or control circuit is outside its operating envelope. Running through an active fault risks compressor, heater, or control-board damage. Diagnose and clear the fault first.

What part is most commonly replaced for Frigidaire Oven Spark Module Replacement - Signs & How-To?

The most frequently replaced parts for Frigidaire Oven Spark Module Replacement - Signs & How-To are listed in the Parts Reference section of this guide with OEM part numbers and typical price ranges. Check the table for direct replacements.

Is Frigidaire Oven Spark Module Replacement - Signs & How-To a DIY repair or do I need a technician?

Sensor swaps, fan motor replacements, and condenser cleaning are typical DIY-level repairs. Anything involving refrigerant, gas, or high-voltage (>240V) work requires a licensed technician for both safety and code-compliance reasons.

Frigidaire Oven Spark Module Replacement - Signs & How-To

Q: What does Frigidaire Oven Spark Module Replacement - Signs & How-To mean?

No spark at burners, intermittent clicking, or burners that won't light mean your spark module has failed. Replacing it restores ignition.

Frigidaire Oven Spark Module Replacement — What This Part Does

The spark module is the ignition control that receives line power and sends timed high-voltage spark output to each of your range’s surface burners. When you turn a knob, the module fires the igniter at that burner so gas lights immediately. The module typically controls all four burners from a single electronic board.

Modules fail internally from heat cycles, voltage spikes, or age. When the board fails, one or more burners lose spark even though gas flows normally and the rest of the range works fine. Loose wire connections at the module or damaged igniter terminals can create the same symptom, so checking those first saves time and money.

Jump to Replacement Steps

Signs It Needs Replacing

No spark at one or more burners You turn the knob and gas flows, but the igniter does not click or spark at all.
Intermittent sparking The igniter clicks on and off randomly, or only sparks after you turn the knob several times.
Burner lights only after repeated attempts You have to turn the knob on and off multiple times before the burner finally ignites.
All burners lose spark at once None of the four burners produce any click or spark, which points directly to module failure rather than individual igniters.
Clicking continues after burner is lit The spark module does not sense flame and keeps sending spark after the burner has already ignited.
Spark at some burners but not others Two burners spark normally while the other two do not, which can indicate a partially failed module or loose terminal connections.

How to Replace It

Disconnect electrical power at the breaker or wall plug, then shut off the gas supply valve to the range.
Remove all grates, burner caps, and burner heads from the cooktop.
Take a photo of the wire connections at the spark module before you touch anything, so you can match each lead to its numbered terminal later.
Remove the screws or fasteners securing the cooktop panel or rear access cover, depending on your model, to expose the spark module.
Inspect the wire harness and each igniter lead at the module for loose, corroded, or misplaced connections, and reseat any suspect wires before condemning the module.
If connections are good and the symptom persists, unplug the wire harness from the old module and remove the mounting screws or release the locking tabs to free the module from its bracket.
Install the new spark module in the same position, secure it with screws or tabs, then reconnect each wire lead to the correct numbered terminal using your photo as a guide.
Reinstall the cooktop panel or access cover, replace burner heads, caps, and grates in reverse order, then restore gas and electrical power.
Test spark at each burner by turning the knob to ignite, and verify that all four burners light promptly and that clicking stops after flame is established.

The Part You Need

Part	Notes
Frigidaire spark module / ignition module	Amazon \| Find your exact model and serial number on the data plate inside the oven door or on the frame behind the warming drawer. Common Frigidaire/Electrolux part numbers include 316135702 and 808, but always confirm fit with your model before ordering.

If this part is failing you may also see one of these codes:

When to Call a Pro

Call a pro if you are not comfortable working with both gas and electrical systems at the same time, or if restoring power and testing spark near an open gas line makes you uneasy. Also call for help if you replace the module and reconnect all wires correctly but still have no spark at any burner, because the fault may be upstream in the range’s power supply or main control board. If only one burner fails to spark after module replacement, the problem is usually a cracked porcelain igniter or damaged wire at that burner, and a technician can diagnose and replace the igniter safely. For gas line, burner, or igniter work, or if you ever smell gas, stop and call a licensed technician.