How do I fix Frigidaire Gas Range Spark Igniter Switch Replacement?

Follow the step-by-step diagnosis below. The most likely fix is identified by checking power, sensor resistance, and control-board signals in order — using a multimeter and the part numbers documented in the parts reference table.

Can I keep running the equipment with this fault active?

Generally no. Faults on Appliance units are emitted when a sensor, safety, or control circuit is outside its operating envelope. Running through an active fault risks compressor, heater, or control-board damage. Diagnose and clear the fault first.

What part is most commonly replaced for Frigidaire Gas Range Spark Igniter Switch Replacement?

The most frequently replaced parts for Frigidaire Gas Range Spark Igniter Switch Replacement are listed in the Parts Reference section of this guide with OEM part numbers and typical price ranges. Check the table for direct replacements.

Is Frigidaire Gas Range Spark Igniter Switch Replacement a DIY repair or do I need a technician?

Sensor swaps, fan motor replacements, and condenser cleaning are typical DIY-level repairs. Anything involving refrigerant, gas, or high-voltage (>240V) work requires a licensed technician for both safety and code-compliance reasons.

Frigidaire Gas Range Spark Igniter Switch Replacement

Q: What does Frigidaire Gas Range Spark Igniter Switch Replacement mean?

When a burner won't spark or sparks continuously, a failed spark igniter switch is often the cause. Replacing the switch and harness assembly restores normal ignition.

Frigidaire Gas Range Spark Igniter Switch Replacement — What This Part Does

The spark igniter switch mounts on each gas valve shaft and sends an ignition signal to the spark module when you turn the knob. When the valve rotates, the switch closes and tells the module to spark the electrode at that burner. The harness carries the signal from each switch to the module, so a complete switch-and-harness assembly is typically replaced as a unit.

These switches fail when internal contacts wear out, when the harness wiring breaks or corrodes, or when the switch isn’t seated properly on the valve stem. Contamination around the valve or control panel can also prevent the switch from actuating fully when you rotate the knob. A bad switch or harness means the module won’t spark the right burner, or it will spark erratically.

Jump to Replacement Steps

Signs It Needs Replacing

One or more burners won’t spark at all Turning the knob produces no clicking sound and no spark at the electrode, meaning the switch isn’t sending the signal to the module.
Wrong burner sparks when you turn a knob The harness wiring is miswired or terminals are swapped at the spark module, so a different burner ignites.
Continuous sparking that won’t stop The switch contacts are stuck closed or the harness is shorted, keeping the spark signal active even after the burner lights.
Intermittent or weak spark Loose or corroded harness connections cause the spark to cut in and out as you rotate the knob.

How to Replace It

Unplug the range or switch off the circuit breaker, then shut off the gas supply valve to the appliance.
Remove the grates, burner caps, and burner bases from the cooktop to access the top and valve area.
Pull off the control knobs and remove the screws or clips securing the control panel to expose the ignition switches and wire harness underneath.
Take a photo or note the wire routing and terminal positions at each switch and at the spark module before disconnecting anything, paying attention to the black and red spark wires.
Check that each switch actuator is physically engaged on the valve stem and that rotating the shaft would close the switch contacts.
Disconnect the old spark ignition switch and harness from the spark module terminals and from each individual switch connector.
Install the new spark ignition switch and harness assembly, routing the wires exactly as the original and connecting each terminal in the correct order at the module and switches.
Reinstall the control panel, secure all screws or clips, then replace the control knobs, burner bases, caps, and grates.
Turn on the gas supply and restore electrical power, then test each burner by turning the knob and verifying proper spark and ignition at the correct burner.

The Part You Need

Part	Notes
Spark ignition switch and harness assembly	Amazon \| Common Frigidaire part numbers include 316580615, 316580611, and 5304494425. Find your model and serial number on the plate inside the oven door or on the side panel to confirm the exact switch assembly for your range.

If this part is failing you may also see one of these codes:

When to Call a Pro

If you’re uncomfortable working around gas lines or tracing ignition wiring, call a qualified appliance technician. Gas burner ignition systems require careful wire routing and terminal placement, and a mistake can cause continuous sparking, burner crossover, or no ignition at all. A pro can also test the spark module (part 808608804) and electrodes to confirm the switches are the actual problem before you order parts. For gas line, burner, or igniter work, or if you ever smell gas, stop and call a licensed technician.