Tag: whirlpool

All the articles with the tag "whirlpool".

• Whirlpool Oven Lock Error Code - Causes & Fix

  31 May, 2026

  Lock or LOC on a Whirlpool oven means Control Lock is active. Hold START for 5 seconds to unlock. F9 means door-lock failure.

• Whirlpool SAB Error Code - Causes & Fix

  31 May, 2026

  SAB (or 5AB/5A6) on a Whirlpool oven means Sabbath Mode is active, not a fault. Exit the mode using your model's control sequence.

• Whirlpool Oven LOC Error Code - Causes & Fix

  31 May, 2026

  LOC means the control lock (child lock) is on, not a fault. Press and hold START/ENTER for 5 seconds to unlock the keypad and clear the display.

• Whirlpool H2O Error Code - Causes & Fix

  31 May, 2026

  H2O means the dishwasher paused the cycle because water fill is not detected. Check water supply is on and inlet hose is not kinked.

• Whirlpool Refrigerator E4 Error Code - Causes & Fix

  31 May, 2026

  E4 on Whirlpool refrigerators usually signals an ice maker fill or bin detection issue. Power-reset and check the ice bin first.

• Whirlpool Refrigerator E0 Error Code - Causes & Fix

  31 May, 2026

  E0 on Whirlpool means no active ice-maker fault in diagnostics, or an ice-maker issue on some models. Check supply, temp, and reset.

• Whirlpool F10E5 Error Code - Causes & Fix

  30 May, 2026

  F10E5 means the cycle ended and drained, then displayed the fault. Most often it's a diverter issue or water leak in the base pan.

• Whirlpool Dishwasher FAE5 Error Code - Causes & Fix

  30 May, 2026

  FAE5 means the cycle ended and drained with a fault. Press Cancel twice and start a new cycle. If it returns, check for leaks in the base pan.

• Whirlpool F8E5 Dishwasher Error - Overfill & Fix

  30 May, 2026

  F8E5 means your Whirlpool dishwasher detected a flood and started draining. Most often water leaked into the base and tripped the float.

• Whirlpool Dishwasher F7E2 Error - Causes & Fix

  30 May, 2026

  F7E2 means high water temperature fault. Usually caused by a failed thermistor or loose sensor connection. Power cycle first.

• Whirlpool F6E3 Dishwasher Error - Causes & Fix

  30 May, 2026

  F6E3 means excessive suds detected. Most often caused by wrong detergent or too much detergent. Remove foam and run empty cycles to clear.

• Whirlpool F4E3 Error Code - Causes & Fix

  30 May, 2026

  F4E3 means the control lost communication with the circulation pump motor. Most often a failed pump motor, loose wiring, or blockage.

• Whirlpool F1E1 Dishwasher Error - Causes & Fix

  30 May, 2026

  F1E1 means your Whirlpool dishwasher starts draining, then stops. Most often a blocked drain hose, bad pump, or control issue.

• Whirlpool Dishwasher E6 Error Code - Causes & Fix

  30 May, 2026

  E6 / F6E6 signals a water supply or filling fault. Check that the shutoff valve is fully open, then reset power for one minute.

• Whirlpool Dishwasher E4 Error Code - Causes & Fix

  30 May, 2026

  E4 means water in the base pan. Most often a loose inlet hose connection. Press Cancel twice, dry the pan, check all fittings.

• Whirlpool Dishwasher E1 Error Code - Causes & Fix

  30 May, 2026

  E1 means a water-fill problem from siphoning. Check the drain hose is looped at least 20 in. above the floor and above the trap.

• Whirlpool E15 Error Code - Causes & Fix

  30 May, 2026

  E15 means water detected in the base leak tray. Most often caused by a worn door seal or loose hose. Dry the base and fix the leak.

• Whirlpool Dryer F4E4 Error Code - Causes & Fix

  30 May, 2026

  F4E4 means low or missing line voltage. Check both breakers and the power cord connections first before calling a tech.

• Whirlpool Dryer F-28 Error Code - Causes & Fix

  30 May, 2026

  F-28 is a communication error in Whirlpool dryers. Most often caused by loose board connectors. Reset the breaker and reseat harnesses.

• Whirlpool Dryer F-01 Error Code - Causes & Fix

  30 May, 2026

  F-01 means electronic control failure. Most likely fix: reset power for 5 minutes, then replace the main control board if code returns.

• Whirlpool F6E2 Error Code - Causes & Fix

  30 May, 2026

  F6E2 means a motor or drive system fault. Power-cycle the dryer for 1 minute, then retest. If it returns, check motor and wiring.

• Whirlpool Dryer F6E3 Error Code - Causes & Fix

  30 May, 2026

  F6E3 means a communication fault between the control board and user interface. Most often fixed by a power reset or control board replacement.

• Whirlpool Dryer F4E2 Error - Causes & Fix

  30 May, 2026

  F4E2 on Whirlpool dryers signals a heater circuit fault. Most often it's a failed heating element or bad wiring connection.

• Whirlpool Dryer F4E3 Error Code - Causes & Fix

  30 May, 2026

  F4E3 means restricted airflow in the exhaust. Clean the lint screen and vent duct to clear the code and restore proper drying.