Tag: appliance

All the articles with the tag "appliance".

• LG Washer Shock Absorber / Suspension Rod Replacement

  8 Jun, 2026

  Excessive vibration, banging, or unbalanced loads during spin point to worn suspension rods or shock absorbers. Replacing them restores tub stability.

• Maytag Washer D3 Error Code - Causes & Fix

  8 Jun, 2026

  D3 means a water temperature sensor error on Maytag top-load washers with temperature-sensing valves. Replace the inlet valve assembly.

• Maytag Washer D16 Error Code - Causes & Fix

  8 Jun, 2026

  D16 on a Maytag commercial washer means the control board cannot communicate with the debit card reader. Check connections first.

• Maytag Washer d13 Error Code - Causes & Fix

  8 Jun, 2026

  d13 is not a standard Maytag code. It's usually a misread display or model-specific diagnostic. Check your manual for the actual code.

• Maytag Washer D1 Error Code - Causes & Fix

  8 Jun, 2026

  D1 (or F03/d1) means a pressure/water-level sensor fault. Most often caused by a pinched, blocked, or disconnected pressure hose.

• Maytag Oven SAB Error Code - Causes & Fix

  8 Jun, 2026

  SAB or SAb means Sabbath Mode is active on your Maytag oven. Press and hold the Clock pad for about 3 seconds to exit the mode.

• Maytag Oven PF Error Code - Causes & Fix

  8 Jun, 2026

  PF means power failure detected. Press Cancel to clear the display, reset the time of day if needed, and check your circuit breaker.

• Maytag Oven LOC Error Code - Causes & Fix

  8 Jun, 2026

  LOC means Control Lock is on, not a fault. Press and hold START for 5 seconds to unlock the control panel and oven door.

• Maytag Oven F9 Error Code - Causes & Fix

  8 Jun, 2026

  F9 or F9 E0 means the control detected incorrect electrical supply wiring, most often L2 and neutral swapped at the terminal block.

• Maytag Oven F7 Error Code - Causes & Fix

  8 Jun, 2026

  F7 means a stuck or shorted function key or keypad fault. Most often a stuck button or failed touchpad. Reset power for 1 minute first.

• Maytag Oven F4 Error Code - Causes & Fix

  8 Jun, 2026

  F4 means a problem with the oven temperature sensor circuit. Most often a bad sensor or loose wiring. Replace the sensor first.

• Maytag Oven F3 Error Code - Causes & Fix

  8 Jun, 2026

  F3 signals an oven temperature sensor circuit fault. Most often the sensor itself has failed; test its resistance before replacing.

• Maytag Oven F2 Error Code - Causes & Fix

  8 Jun, 2026

  F2 means the oven temperature exceeded its safe limit or the sensor circuit failed. Most often a bad temperature sensor or probe.

• Maytag Oven F1 Error Code - Causes & Fix

  8 Jun, 2026

  F1 means the control lost the oven temperature sensor signal. Most often a failed sensor. Reset power, test sensor, or replace it.

• Maytag Oven F0 Error Code - Causes & Fix

  8 Jun, 2026

  F0 or F0 E0 means a stuck function key or unrecognized control fault. Most often a stuck touchpad key. Reset power first.

• Maytag Oven CAL Error Code - Causes & Fix

  8 Jun, 2026

  CAL means your Maytag oven is in calibration mode, not a fault. Exit the mode by pressing Cancel or cycle power for 1 minute to clear.

• Maytag Oven AB Error Code - Causes & Fix

  8 Jun, 2026

  AB on a Maytag oven usually means Sabbath mode is active, not a fault. Cancel Sabbath mode through your control or power-cycle the unit.

• Maytag Oven A6 Error Code - Causes & Fix

  8 Jun, 2026

  A6 is not a standard Maytag oven code. Most likely a misread display, Sabbath mode, or control glitch. Power reset first.

• Maytag Dryer PF Error Code - Causes & Fix

  8 Jun, 2026

  PF means power failure: the dryer lost power during the cycle. Most often a tripped breaker or loose connection. Hold START to restart.

• Maytag Dryer L2 Error Code - Causes & Fix

  8 Jun, 2026

  L2 means low or no line voltage to the heater. The dryer tumbles but won't heat. Check your 240 V breaker and reset both poles fully.

• Maytag Dryer F2E1 Error Code - Causes & Fix

  8 Jun, 2026

  F2E1 means a keypad fault on your Maytag dryer. Most often a stuck button or contamination on the console. Power reset first.

• Maytag Dryer F9E2 Error Code - Causes & Fix

  8 Jun, 2026

  F9E2 is not a standard Maytag dryer code. You likely saw F3E2 (moisture sensor fault). Clear by pressing Power, then reset the breaker.

• Maytag Dryer F78 Error Code - Causes & Fix

  8 Jun, 2026

  F78 means a power supply or voltage fault. Reset the breaker for 5 minutes, then run Timed Dry. Check for missing leg or loose wiring.

• Maytag Dryer F77 Error Code - Causes & Fix

  8 Jun, 2026

  F77 is not a standard Maytag dryer code. Likely a misread display or model-specific fault. Power reset and verify the exact code first.