What this code means
A163 does not appear in verified Weil-McLain fault code documentation. The exact meaning depends on your boiler model and control platform. Weil-McLain uses numbered error codes on platforms like the AquaBalance control, but A163 is not confirmed as a standard fault identifier. Your display may be showing a control-specific diagnostic number, a lockout condition, or a sensor reading rather than a universal error code.
Because the code is not documented, verify the exact model and CP number from the boiler jacket label and consult your owner’s manual or the wiring diagram inside the front panel. Common fault categories on Weil-McLain boilers include ignition failure, flame sensing faults, temperature sensor errors, low water or pressure conditions, and circulation problems. Until you confirm the code meaning for your specific control, treat this as a general lockout or fault and follow the manufacturer’s troubleshooting workflow.
Before You Replace Anything
Many technicians replace the main control board when the real problem is a dirty or misaligned flame rod. Clean and inspect the flame sensor and test continuity before ordering a new control.
Common Causes
- Ignition or flame sensing fault A dirty, warped, or misaligned igniter or flame rod prevents the control from proving flame and causes a lockout.
- Temperature sensor fault A failed thermistor or temperature probe sends false readings to the control and triggers a fault condition.
- Low system pressure or water level Pressure below minimum or air in the system prevents circulation and the control locks out to protect the boiler.
- Gas supply issue Weak gas pressure, a closed manual shutoff, or a faulty gas valve prevents ignition and triggers a lockout.
- Control board or wiring fault Internal control failure or a loose harness connection causes the board to report an error or fail to complete the ignition sequence.
- Circulator or pump fault A stuck or failed circulator prevents flow and the control shuts down on a flow or temperature limit.
Step-by-Step Fix
- Verify the exact boiler model and control. Locate the jacket label or rating plate and write down the model number and CP number. Check the owner’s manual or wiring diagram inside the front panel for a fault code table that includes A163.
- Read the fault history. Access the diagnostic menu on your boiler control or remote display. Note the last fault code, lockout status, and any sensor readings shown. Compare these to the manufacturer’s documentation.
- Check system pressure and refill if needed. Look at the pressure gauge on the boiler. If pressure is below 12 psi, open the fill loop valve slowly until the gauge reads about 15 psi, then close the valve. Bleed air from radiators or zone valves if present.
- Inspect the igniter and flame rod. Turn off power and gas. Remove the burner access cover. Clean the igniter and flame rod with fine steel wool or emery cloth. Check for cracks, warping, or misalignment. Reinstall and verify proper spacing per the wiring diagram.
- Test for gas supply. Confirm the manual gas shutoff upstream of the boiler is fully open. Turn on power and listen for the gas valve to click when the boiler calls for heat. If you smell gas but see no flame, the igniter may be weak or the gas valve may be stuck.
- Test temperature sensors. Disconnect power. Unplug the supply or return thermistor from the control board. Measure resistance with a multimeter and compare to the manufacturer’s temperature-resistance chart. Replace the sensor if readings are out of range or if the sensor is physically damaged.
- Reset the control and monitor. After completing repairs, restore power and gas. Press and hold the reset button on the control for three seconds. Observe the ignition sequence through the inspection window. If the code returns or the boiler locks out again, call a licensed heating technician to test the control board, gas valve, and wiring harness.
Parts Often Needed
| Part | Notes |
|---|---|
| Flame rod or flame sensor | Amazon | Verify your model’s part number from the wiring diagram before ordering. |
| Igniter or hot surface ignitor | Amazon | Match the igniter style (flat or round) and connector to your burner assembly. |
| Temperature sensor or thermistor | Amazon | Identify whether you need the supply or return sensor from the fault description. |
| Gas valve | Amazon | Professional replacement required. Confirm voltage and gas type before ordering. |
When to Call a Pro
Call a licensed heating contractor immediately if you cannot find A163 in your boiler’s documentation, if you smell gas, if the boiler repeatedly locks out after reset, or if you are not comfortable working with gas appliances. Professional help is required for gas valve replacement, control board diagnostics, venting inspection, and any fault that involves testing or adjusting gas pressure. Weil-McLain recommends contacting a qualified heating contractor to identify the exact model, interpret control-specific fault codes, and obtain warranty parts. Do not attempt to bypass safety lockouts or modify control wiring.