Posts

All the articles I've posted.

• LG Dishwasher E1 Error Code - Causes & Fix

  7 Jun, 2026

  E1 means a leak or overfill triggered the float switch. Most often water pooled in the base pan from a door seal or internal leak.

• LG Dishwasher CR Error Code - Causes & Fix

  7 Jun, 2026

  CR means your LG dishwasher is stuck in Test Mode (Continuous Run). Turn the unit off at the breaker for 30 seconds, then power back on.

• LG Dishwasher CE Error Code - Causes & Fix

  7 Jun, 2026

  CE is a motor error on LG dishwashers. The wash motor or its wiring harness has failed. Reset power, check connections, replace motor if needed.

• LG Dishwasher bE Error Code - Causes & Fix

  7 Jun, 2026

  bE means bubble error: too many suds. Fix: confirm you're using dishwasher detergent (not dish soap), run empty cycle to clear foam.

• LG Dishwasher AE Error Code - Causes & Fix

  7 Jun, 2026

  AE means water in the base pan triggered the leak sensor. Most often caused by a dirty door gasket. Dry the pan and find the leak source.

• Samsung Washer UC Error Code - Causes & Fix

  7 Jun, 2026

  UC means power supply or voltage problem. Most often caused by unstable line voltage or using an extension cord. Plug directly into a dedicated circuit.

• Samsung Washer UB Error Code - Causes & Fix

  7 Jun, 2026

  UB means unbalanced load. The drum is weighted to one side during spin. Pause, untangle and redistribute laundry, then restart.

• Samsung Washer tE2 Error - Causes & Fix

  7 Jun, 2026

  tE2 means a temperature sensor circuit fault. Most often a bad thermistor or loose connector. Check wiring and sensor resistance first.

• Samsung tE1 Error Code - Causes & Fix

  7 Jun, 2026

  tE1 on Samsung washers means a temperature-sensor fault. Most often a bad sensor or loose connector. Check the thermistor first.

• Samsung Washer tE Error Code - Causes & Fix

  7 Jun, 2026

  tE means temperature sensor fault. Most often a failed thermistor or loose connector. Check sensor resistance and wiring first.

• Samsung Washer tC Error Code - Causes & Fix

  7 Jun, 2026

  tC means thermistor/temperature sensor fault. Most common fix: replace the failed thermistor or repair damaged wiring to the sensor.

• Samsung Washer OE Error Code - Causes & Fix

  7 Jun, 2026

  OE means overflow/overfill detected. Most often a stuck-open inlet valve or faulty water-level sensor. Check drain filter and valve first.

• Samsung Washer LE1 Error Code - Causes & Fix

  7 Jun, 2026

  LE1 signals a water-level sensor fault or leak detection. Most often a water leak into the base pan triggers it. Dry the pan and check sensor wiring.

• Samsung LC1 Error Code - Causes & Fix

  7 Jun, 2026

  LC1 means the washer detected a leak or water-level drop during wash/rinse. Most often trapped water or suds at the leak sensor.

• Samsung HE1 Error Code - Causes & Fix

  7 Jun, 2026

  HE1 means a heater error in your Samsung washer's water-heating system. Most often caused by a failed heating element or thermistor.

• Samsung Washer HE Error Code - Causes & Fix

  7 Jun, 2026

  HE means heating error on Samsung washers. Most often caused by a failed thermistor or heater element. Check water supply and power-reset first.

• Samsung Washer E3 Error Code - Causes & Fix

  7 Jun, 2026

  E3 on Samsung washers usually means motor feedback fault. Most common cause: loose motor harness or worn brushes (brushed motors).

• Samsung Washer dE Error Code - Causes & Fix

  7 Jun, 2026

  Samsung dE/dE1/Ed/dC/DC code means the door is not sensed as closed. Most often laundry is caught in the seal or the door is not latched.

• Samsung Washer CE Error Code - Causes & Fix

  7 Jun, 2026

  CE means a temperature-sensing or cooling fault. Most often: hot and cold inlet hoses are reversed. Swap them to match cold-to-cold.

• Samsung Washer bE3 Error Code - Causes & Fix

  7 Jun, 2026

  bE3 means a button on the control panel is stuck or shorted. Most often caused by a stuck key or debris around the buttons.

• Samsung Washer bE2 Error Code - Causes & Fix

  7 Jun, 2026

  bE2 means a stuck or jammed button on the control panel (or MEMS sensor fault on some models). Most often fixed by cleaning buttons.

• Samsung Washer bE1 Error Code - Causes & Fix

  7 Jun, 2026

  bE1 means a control-panel button is stuck or continuously pressed. Clean the buttons and power-cycle the washer to clear it.

• Samsung bE Error Code - Causes & Fix

  7 Jun, 2026

  Samsung bE means a button is stuck or jammed on the control panel. Clean around buttons and press each one to release it.

• Samsung Washer bC1 Error Code - Causes & Fix

  7 Jun, 2026

  bC1 means a button is stuck or held down, usually the Power button. Clean the keypad and power-cycle. Most often fixes a stuck button.