Posts

All the articles I've posted.

• Whirlpool Dryer F-28 Error Code - Causes & Fix

  7 Jun, 2026

  F-28 means a control-system communication fault. Most often a loose or corroded connector between boards. Reset power, reseat harnesses.

• Whirlpool Dryer F-22 Error Code - Causes & Fix

  7 Jun, 2026

  F-22 means the exhaust thermistor circuit is open or shorted. The most common fix is replacing the failed exhaust thermistor sensor.

• Whirlpool Dryer F-02 Error - Causes & Fix

  7 Jun, 2026

  F-02 on a Whirlpool dryer means a stuck key or control panel fault. Power down for 5 minutes, restart, and run a timed cycle to clear it.

• Whirlpool Dryer F-01 Error Code - Causes & Fix

  7 Jun, 2026

  F-01 means a main control board communication fault. The most common fix is replacing the control board or repairing a failed relay.

• Whirlpool H2O Error Code - Causes & Fix

  7 Jun, 2026

  H2O means the dishwasher cycle paused because water supply is insufficient. Check that the shutoff valve is fully open and hose is unkinks.

• Whirlpool Dishwasher FAE5 Error Code - Causes & Fix

  7 Jun, 2026

  FAE5 means the cycle ended with a drain and an error. Press Cancel twice and run a new cycle. Recurring faults need diagnosis.

• Whirlpool Dishwasher F9E1 Error - Causes & Fix

  7 Jun, 2026

  F9E1 means the dishwasher can't drain. Most often the garbage disposer knockout plug wasn't removed or the drain hose is kinked or clogged.

• Whirlpool Dishwasher F8E4 Error Code - Causes & Fix

  7 Jun, 2026

  F8E4 means water is in the drip tray under your Whirlpool dishwasher. Check inlet connections, empty the tray, and restart.

• Whirlpool Dishwasher F8E2 Error Code - Causes & Fix

  7 Jun, 2026

  F8E2 signals a bulk dispenser system fault. Most often a clogged dispenser or missing detergent. Power reset, clean, and reseat the unit.

• Whirlpool Dishwasher F7E2 Error - Causes & Fix

  7 Jun, 2026

  F7E2 means a wash motor or circulation pump fault. Most common fix: cycle power for 1 minute, then check for debris blocking the impeller.

• Whirlpool Dishwasher F6E4 Error - Causes & Fix

  7 Jun, 2026

  F6E4 means the overfill float switch is triggered. Most often caused by an unlevel machine or water in the base pan from a leak.

• Whirlpool F6E3 Dishwasher Error - Causes & Fix

  7 Jun, 2026

  F6E3 means excess suds detected. Most common fix: remove foam with oil, run empty cycle. Usually caused by wrong detergent or overuse.

• Whirlpool Dishwasher F6E1 Error Code - Causes & Fix

  7 Jun, 2026

  F6E1 means the dishwasher cannot start or resume cycles. Power-cycle the unit first. If it persists, check the door latch.

• Whirlpool F4E3 Error Code - Causes & Fix

  7 Jun, 2026

  F4E3 on Whirlpool dishwashers means the wash motor is not running. Most often a clogged pump or seized motor. Reset power first.

• Whirlpool Dishwasher F2E2 Error Code - Causes & Fix

  7 Jun, 2026

  F2E2 means the control cannot communicate with the user interface. The most common fix is replacing the UI console or reseating connectors.

• Whirlpool F1E1 Dishwasher Error - Causes & Fix

  7 Jun, 2026

  F1E1 means the drain sequence starts but the dishwasher stops. Most often a stuck relay or control board fault. Reset power first.

• Whirlpool F10E5 Error Code - Causes & Fix

  7 Jun, 2026

  F10E5 (FAE5) means a diverter fault. The dishwasher drains and stops. Most often caused by a leaking diverter gasket at the sump.

• LG Washer tE Error Code - Causes & Fix

  7 Jun, 2026

  tE means a heating or temperature-sensing fault. The most common fix is replacing the faulty thermistor (temperature sensor).

• Whirlpool F1E1 Error Code - Causes & Fix

  7 Jun, 2026

  F1E1 means a stuck relay on the main control board. Most often the control board itself has failed and needs replacement.

• LG Washer SE Error Code - Causes & Fix

  7 Jun, 2026

  SE means sensor error. Power off, unplug for 10 seconds, reconnect, and retry. If the code returns, call LG service for diagnosis.

• LG Washer SUD Error Code - Causes & Fix

  7 Jun, 2026

  SUD means too many suds detected. The washer extends the cycle up to 2 hours to clear foam. Most often caused by too much detergent or non-HE soap.

• LG Washer PE Error Code - Causes & Fix

  7 Jun, 2026

  PE means the water level sensor can't detect tub level. Most often a kinked or blocked pressure hose. Check hose first, then sensor.

• LG Washer PF Error Code - Causes & Fix

  7 Jun, 2026

  PF means power failure. The washer lost electricity during a cycle. Press and hold START/PAUSE for 5 seconds while unplugged to reset.

• Samsung Oven tE Error Code - Causes & Fix

  7 Jun, 2026

  Samsung oven tE code signals a temperature sensor or thermistor circuit fault. The most common fix is replacing the oven temperature sensor.