Posts

All the articles I've posted.

• Electrolux Dryer E97 Error Code - Causes & Fix

  10 Jun, 2026

  E97 means a program mismatch inside the main control board. The most common fix is resetting the dryer or replacing the control board.

• Electrolux Dryer E73 Error Code - Causes & Fix

  10 Jun, 2026

  E73 means the inlet thermistor is reading out of range. Most often a failed inlet thermistor on the heater duct; replace the sensor.

• Electrolux Dryer E72 Error Code - Causes & Fix

  10 Jun, 2026

  E72 means the outlet thermistor is out of range. Most often a failed thermistor or loose wiring. Test resistance at ~5,000Ω (70°F).

• Electrolux Dryer E71 Error Code - Causes & Fix

  10 Jun, 2026

  E71 means the outlet thermistor circuit failed. Most common fix: replace the faulty outlet temperature sensor or repair its wiring.

• Electrolux Dryer E61 Error Code - Causes & Fix

  10 Jun, 2026

  E61 means heater relay or heating-circuit fault. Most often a stuck relay on the main control board or grounded heating element.

• Electrolux Dryer E54 Error Code - Causes & Fix

  10 Jun, 2026

  E54 means drive motor relay circuit failure. Most common fix: check incoming power voltage, test the start capacitor, and inspect for mechanical overload.

• Electrolux Dryer E51 Error Code - Causes & Fix

  10 Jun, 2026

  E51 means motor relay or motor power triac failure. Most common fix: replace the main control board after checking motor wiring.

• Electrolux Dryer E42 Error Code - Causes & Fix

  10 Jun, 2026

  E42 means the door sensing circuit failed. The door switch cannot tell the control board the door is closed. Replace the door switch.

• Electrolux Dryer E31 Error Code - Causes & Fix

  10 Jun, 2026

  E31 means moisture sensor frequency too high. Clean sensor bars in the drum first-buildup is the most common cause.

• Electrolux Dryer E09 Error Code - Causes & Fix

  10 Jun, 2026

  E09 on Electrolux dryers usually signals a control-electronics or relay fault. Check your model's manual for the exact meaning.

• Electrolux Dryer AD Code - Causes & Fix

  10 Jun, 2026

  AD means Auto Dry mode is selected, not a fault. If cycles run poorly, clean the moisture sensor bars with alcohol. That fixes most issues.

• Kenmore Washer F0 E4 Error Code - Causes & Fix

  10 Jun, 2026

  F0 E4 means wash water is too hot. Most common fix: hot and cold fill hoses are swapped at the wall or at the washer inlet.

• Kenmore Washer F0 E2 Error - Causes & Fix

  10 Jun, 2026

  F0 E2 means excessive suds detected in the basket. Most common fix: switch to HE detergent and use less of it per the dispenser cap.

• Kenmore Oven F7 Error Code - Causes & Fix

  10 Jun, 2026

  F7 on Kenmore ovens means a keypad or touchpad failure, usually a stuck key or shorted membrane. Most often fixed by reseating or replacing the keypad.

• Kenmore Oven F4 Error Code - Causes & Fix

  10 Jun, 2026

  F4 means the oven temperature sensor circuit is open, shorted, or out of range. The most common fix is replacing the sensor probe.

• Kenmore Oven F31 Error Code - Causes & Fix

  10 Jun, 2026

  F31 means the oven temperature sensor circuit is shorted. The most common fix is replacing the failed RTD sensor probe.

• Kenmore Oven F30 Error Code - Causes & Fix

  10 Jun, 2026

  F30 means the oven temperature sensor circuit is open or not reading correctly. The most common fix is replacing the sensor probe.

• Kenmore Oven F3 Error Code - Causes & Fix

  10 Jun, 2026

  F3 on a Kenmore oven means an oven temperature sensor circuit fault. Most often the sensor probe itself has failed and needs replacement.

• Kenmore Dryer F74 Error Code - Causes & Fix

  10 Jun, 2026

  F74 on a Kenmore dryer means different things by model. Check your tech sheet first. Often a wiring or control board fault.

• Kenmore Dryer F72 Error Code - Causes & Fix

  10 Jun, 2026

  F72 means user interface control assembly failure. Most often the UI board itself has failed. Power reset, inspect harness, replace UI board.

• Kenmore Dryer F70 Error Code - Causes & Fix

  10 Jun, 2026

  F70 means no communication between the user interface and main control board. Most often a loose or corroded wire connector.

• Yaskawa A1000 oL7 Fault - Causes & Fix

  10 Jun, 2026

  oL7 means High Slip Braking overload: the motor could not stop in time. Most common fix: lengthen deceleration time in your ramp settings.

• Yaskawa A1000 oL6 Fault - Causes & Fix

  10 Jun, 2026

  oL6 means motor thermal overload on the Yaskawa A1000. Most often caused by excessive mechanical load or incorrect motor parameters.

• Yaskawa A1000 oL5 Fault - Causes & Fix

  10 Jun, 2026

  oL5 means Mechanical Weakening Detection 1: the drive detected overtorque matching the threshold in parameter L6-08. Check for binding.