Posts
All the articles I've posted.
-
GE Oven Won't Stop Beeping - Causes & Fix
Usually the Cooking Complete Reminder after a cycle ends. Press Clear/Off or open the door to stop the once-per-minute beep.
-
Whirlpool Oven Display Not Working - Causes & Fix
A blank Whirlpool oven display usually means a tripped circuit breaker or failed control board. Reset the breaker for 1 minute first.
-
Whirlpool Oven Clicking but Won't Light - Causes & Fix
A bad igniter or spark module is usually the culprit. Check gas supply, inspect the igniter for a weak glow, and replace as needed.
-
Whirlpool Oven Heats Too Hot - Causes & Fix
Most often a faulty temperature sensor (should read ~1,080 Ω at room temp). Test sensor resistance, inspect wiring, and replace if out of spec.
-
Whirlpool Oven Won't Stop Beeping - Causes & Fix
Usually caused by Control Lock being engaged or something pressing on the control panel. Press OFF/CANCEL to clear alerts first.
-
LG Oven Display Not Working - Causes & Fix
Loose wiring harness between control and display boards causes most blank screens. Reseat connectors or replace control board.
-
LG Oven Clicking but Won't Light - Causes & Fix
Usually a weak bake igniter that glows but can't draw enough current to open the gas valve. Replace the igniter if it glows over 90 seconds without lighting.
-
LG Oven Heats Too Hot - Causes & Fix
A failed temperature sensor or thermistor is the most common cause. Replace the sensor and verify wiring before replacing the control board.
-
LG Oven Won't Stop Beeping - Causes & Fix
Usually a power outage alarm (PO/PF code) or a thermistor fault. Press Power OFF/ON first, then flip the breaker for 30 seconds to reset.
-
LG Oven Igniter Not Working - Causes & Fix
Most LG gas ovens fail to ignite when the bake igniter is too weak to draw enough current to open the valve. Replace the igniter.
-
Samsung Oven Display Not Working - Causes & Fix
Usually caused by a failed main control board or user interface board. Check power supply, reset the unit, then test DC voltages at connectors to isolate the fault.
-
Samsung Oven Clicking but Won't Light - Causes & Fix
Usually a weak igniter that clicks or glows but can't open the gas valve. Test igniter current draw and replace if below spec.
-
Samsung Oven Heats Too Hot - Causes & Fix
A faulty temperature sensor reading incorrectly is the most common cause. Test the sensor for about 1000 ohms at room temperature and replace if out of range.
-
Samsung Oven Self-Clean Not Working - Causes & Fix
Usually a failed door lock assembly or latch microswitch that prevents the cycle from starting or causes it to abort mid-cycle.
-
Samsung Oven Won't Stop Beeping - Causes & Fix
Most often the sound setting was toggled on in the control menu. Enter Settings, go to option 5, and turn sound off to stop beeping.
-
Kenmore Dishwasher Buttons Not Working - Causes & Fix
A failed touchpad membrane is the most common cause when buttons won't respond. Replace the control panel assembly after checking for control lock and power cycling the unit.
-
Kenmore Dishwasher Won't Latch - Causes & Fix
Usually a misaligned strike or worn latch hook. Inspect the door latch assembly and strike for damage, then test the latch switch.
-
Kenmore Dishwasher Standing Water in Bottom - Causes & Fix
A clogged filter or blocked drain hose prevents the sump from evacuating. Remove power, clean the filter and sump, check the hose for kinks or clogs.
-
Kenmore Dishwasher Not Dispensing Detergent - Causes & Fix
Usually caused by dish loading blocking the dispenser door. Check for obstructions, clean the cup and latch, then test the actuator.
-
Kenmore Dishwasher Smells Bad - Causes & Fix
Usually a dirty filter or trapped food debris in the sump. Pull the lower rack, remove and clean the filter and screen, then run a hot cycle.
-
Kenmore Dishwasher Won't Fill With Water - Causes & Fix
Usually a clogged or failed water inlet valve. Check the valve screen for debris and test the valve coil for around 1,400 ohms resistance.
-
Kenmore Dishwasher Stuck Mid Cycle - Causes & Fix
Usually a door latch or door switch failure. Check latch engagement and alignment first, then test inlet valve and drain system.
-
Amana Washer PF Error Code - Causes & Fix
PF means a power failure interrupted the cycle. Press and hold START to restart, or press POWER to clear the display.
-
Amana Washer LdU Error Code - Causes & Fix
LdU means the lid cannot unlock. Remove all items from the top of the washer, including laundry baskets, and clear any debris around the lid.